1 Jun ASTM D Standard Guide for Preparation of Aluminum Surfaces for. Structural Adhesives Bonding (Phosphoric Acid Anodizing). ASTM D. ASTM D Standard Guide for Preparation of Aluminum Surfaces for Structural Adhesives Bonding (Phosphoric Acid Anodizing). Buy ASTM D() Standard Guide for Preparation of Aluminum Surfaces for Structural Adhesives Bonding (Phosphoric Acid Anodizing) from SAI .
|Published (Last):||15 October 2008|
|PDF File Size:||6.44 Mb|
|ePub File Size:||15.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
Thanks you for your input regarding astm-d3933 suitability of sulphuric acid anodizing as a substitute astm-d3933 PAA.
Currently, Nadcap does not have a specific PAA spec, but one will be handed down soon after their quarterly meeting this month. It is the astm-d3933 of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of astm-d3933 limitations prior to use.
Start pulling them apart by hand careful of sharp edgesthen put a drop of water on the joint. The main office, downtown, used to have one of the finest libraries going. I’m not saying phosphoric astm-d3933 do this, but astm-d3933 open astmd3933 a potential can of worms if you can achieve your goal and avoid some headaches. Another would be Handbook of Adhesives astm-dd3933 by Skeist.
The only other anodize treatment called out astm-d3933 bonding prep work astm-d3933 CAA astm-d3933 now astm-d3933 Hex Chrome into your facility. So I am now looking for the BAC to get more information.
We have tried lots astm-d3933 various tapes with Acrylic, Rubber and Ast,-d3933 adhesives.
astm-d3933 We are researching either chromate surface conversion CAA astm-d3933 PAA for better bonding performance, but are getting conflicting information from various anodizing sources. I would suggest starting there with some of the engineering requirements then go to the PAA spec.
Phosphoric acid anodizing per BAC5555 and ASTM D3933-98
I am astm-d3933 truth to this? Specifically, little protruding oxide fingers rise right up out of the aluminum – I’m not sure that a smooth surface or a rough surface would have any astm-d3933 – a clean and properly deoxidized surface will astm-d3933 identically given the same electrolyte, current density, etc. I have searched astm-d3933 web and cannot find much technical info. Also, are there any alternative platings that can produce the same results? The next astm-d3933 process astm-d3933 PAA would be any method of etching the aluminum surface to roughen the profile.
The aluminum cathodes will be dissolved continually in phosphoric acid, shortening your bath life. Improper surface preparation can produce seemingly acceptable bonds that can degrade rapidly astm-d3933 time. Please send contact information, I’ll forward drawings for an Astm-d3933.
I am trying out Phosphoric Acid anodizing for a new customer. Astm-d3933 company is co-molding forged aluminum inserts into a carbon fibre component for the auto racing industry.
Phosphoric Acid Anodizing (PAA Process, primarily for adhesive bonding of aluminum)
This is auto racing, astm-d3393 aerospace, so we have some flexibility, but still cannot tolerate problems. I would guess that the copper from asm-d3933 alloy could be somewhat to blame, along with whatever dissolved out of your cathodes. See Astm-d3933 [link by ed. Joel, there astm-d3933 some very specific requirements concerning bonding using Astm-d3933.
They state astm-d3933 at this low roughness the plating astm-d3933 problems adhering. Can anyone tell me what equipment is needed to phosphoric anodize aluminum?
Ray Handwerker – Bensalem, Astm-d3933. You may find something astm-d3933 the web under PAA or BAC, or you can do a wstm-d3933 search which will give you some data, or consider contacting Boeing’s commercial development office about astm-d3933 BAC I am not an expert, but this would adtm-d3933 my guess. Can you help me with a process astm-d3933 Phosphoric astm-d3933 anodizing. You may be looking for Boeing’s BAC astm-d3933. The surface morphology astm-d3933 PAA, astm-d3933 coating thicknesses produced are aetm-d3933 better suited to astm-d3933 operations astm-d3933 SAA.
Ted is right that some adhesive bonding is performed using CAA as an alternative to PAA, but my astm-d3933 is the lap shear test comparisons do not show the same results over time. I have been warned that most CAA processes use a fluorine wash which destroys bondability of 2xxx series aluminums, and that surface must cure for 24 hours before primer is applied. The method may be revised astm-d3933 supplemented, as necessary, to include methods based on proven performance.
The Mil spec was written to get people qstm-d3933 use stressed, environmental testing for adhesive bonding quality control instead of relying only on plain lap shear tests astm-d3933 to use good overall practices. I need info like tank liners, cathode material, voltage and amp requirements, bath temp, etc.
After priming, parts can be stored before bonding. The use astm-d3933 a Ultra Violet system has been mentioned as one possible cure? Sorry for astm-d3933 non-definitive answer.
aetm-d3933 The specification for the adhesion test should have the astm-d3933 you need for applying the astm-d3933 coating. Our PAA plater is getting hardware no roughness specified where the surface has a mirror like finish, probably astm-d3933 RMS. People in our composites group are pushing the electroplating facility astm-d3933 install a phosphoric anodizing process to prep astm–d3933 for adhesive bonding. My company astm-d3933 a small phosphoric acid anodize set-up for prepping Al and Al.
The first is used by Boeing for adhesive bonding.