ASTM Automation/Robotics LIS which are based on ASTM E / . In the ASTM-Serial interface, ASTM E and E “ASTM /”, operation should be performed in ASTM E mode. *2: IEEE e) Date/time test completed. This document describes the electronic transmission of digital information .. In , ASTM Committee E31 decided to restructure its operations, with the intent .
|Published (Last):||10 October 2010|
|PDF File Size:||4.46 Mb|
|ePub File Size:||13.67 Mb|
|Price:||Free* [*Free Regsitration Required]|
Thank you for reply. You also need to make certain the serial cable is correct as the document displays such that certain pins only aatm used and jumpered appropriately wherever those ends of the serial cable go prior to doing anything or else the communications may not work.
VB 1381–95, December 8, Saturday, December 13811-95, Unless you connect each to a DCE device for some reason. Thursday, December 8, If you have access to the user manual you could indicate where you got it from, and if it’s accessible then someone may be able to look at it for you. Receiving messages and acknowledge of astn transmissions are notified by callbacks to the ee implementations of the driver-defined callback classes. There were no books found for the applied search filters.
Messages can be created, edited, transmitted, received, saved to file and 13381-95 from file. Your code assumes that the device transmits text – that may not be the case. As for nowI have gone past most “issues” i am facing with this device. So you probably need to find Astj, E and purchase or read from Scribd or some other source and I have no idea what Scribd is or if it is reputable the entire Host Interface Manual if in fact that is the correct Host Interface Manual for the “Roche Diagnostics GmbHElecsys Analyzer” which I’ve no idea if it is for the I hope you didn’t think that I’d go about connecting this equipment without having configured the port setting already.
Thursday, December 8, 2: If you have the make and model number of the equipment it is likely that a search of the www will reveal on-line documentation, or at least some comments from someone who has tried to do it before. Enter your account email address to request a password reset: Friday, December 16, Monkeyboy Friday, December 9, 4: Did you ever find and read a Host Interface Manual for the ?
ASTM Connector Information
Or perhaps the Interface Training Guide is wrong which is doubtful but possible. So i finally figured out what was the exact problem. According to the information posted d E sends ENQ which is invisible control character. However the training guide says ” ASTM standards – The low-level protocol, E, describes how the data is transmitted between the and host.
It is unlikely that most of it will work in the same manner, and even when you get it communicating you still have to decode the data it is transmitting. Monday, December 5, 7: Lastly I would like to thank you Mr. And the wire from 7 to 8 in the bottom pic on the left DB9 connector does NOT also connect to pin 3 which it crosses over in the image which in the image really doesn’t matter if the DB9 is male 13811-95 female. He can choose to retry the failed message, continue with the next message or to discard all messages remaining in an idle state.
And from what I understand the messaging protocol is not simple to learn and you will probably not have knowledge about what messages the may use without getting its Host Interface Manual but I’m not really sure asrm that. It isn’t going to do any good if you don’t have all that information to read and study prior to even bothering trying to communicate with the device really.
Now I am starting to doubt that the equipment itself has a problem maybe the whole 9DB connector is broken from inside so before I attempt any thing on the equipment itself I have ordered the Serial Tester you recommended just to know for sure that there is actually no 11381-95 sent out from the E at all.
You may be able to loop the pins within the connector, or you may be able to drive CTS from the PC end if your cable is wired through by setting the right signal probably RTS when you open the PC port.
Search book title Enter keywords for book title search. Saturday, December 3, 9: Very often, searching for other models in the same range will reveal enough detail.
ast No further reproductions authorized. Anyhow link is displayed in image below from Google. And since you don’t seem proficient in serial communications testing then it may be necessary to hire a professional to bring in a serial port protocol analyzer to test with the Jumpering means physically connecting the pins together with a piece of wire so that, in this instance, those two pins for the end of the cable connecting into the are physically connected together.
An actual serial interface protocol analyzer would display everything about the ‘s DB9 port from asgm it is set to to what data is sent by it. The driver divides it in pieces of the maximal frame f that is allowed by the standard and transfers each frame to the host.
There could’ve been others that are better or worse. Enter your personal account email address to request a password reset: The client does not deal with any details such as record number, field separators, field order and record hierarchy. A digital multimeter display on the data line will also flicker. I mean I successfully connected other similar devices and was able to get the results I needed.
ASTM Connector Information – [PDF Document]
This asynchronous callback mechanism prevents processor-time consuming polling. Register for a trial account. Monkeyboy Thursday, December 8, 3: Or it’s possible the port is malfunctioning and without checking it then that can not be proven either way. Then you have no option but to get the information from the manufacturer concerning how to initiate a data transfer. RS serial communication is a black art. But basically if the PC and both use DB9 interfaces the bottom pic would be the pins used.
ASTM Simulator is a flexible and very powerful productivity tool for prototype testing,system verification, system installation and troubleshooting ASTM communication interfaces. Friday, December 9, 2: I am assuming the problem could be with the the setting.